Workholding
Contact
Series
B1.8320

Electric Swing Clamps

Parallel drive, position and clamping force monitoring, IO-Link connection optional, DC voltage 24 V, minimum energy demand
Electric Swing Clamps
Downloads
Catalogue sheet
Operating instructions
Information Series
Description
B 1.8320 Electric Swing Clamps - Parallel drive

IO-Link connection optional

The electric swing clamp is driven by a wear-resistant brushless DC motor. The motor speed is transformed by means of a gear and a threaded spindle into the swing and stroke movement of the piston rod.
For swinging the clamping arm by 180°, an axial stroke of only 3 mm is required.
If the clamping arm collides during the swing motion with a workpiece, the mechanism is protected against overload.  
The direct current motor is automatically and immediately switched off. When unclamping, the clamping arm always swings back to the off-position.

Integrated control
The electronic control for the DC motor is on a board in the housing of the electric swing clamp.

Electric connection
Power supply and signal exchange for external control are transmitted by two short cables with plug-type connector. Cable sockets are available for the customer's connection (see connection accessories). 

Safe touch voltage
The used DC voltage 24 V is considered to be a "low voltage" and thus it is not dangerous for people in case of contact.

Power supply
For motor and electronic control a DC voltage of 24 V with a residual ripple of max. 10 % is required.
For the DC motor, we recommend the use of a switching power supply with a current output of 15 A per connected electric swing clamp. When operating several swing clamps at the same time, the line is to be enlarged correspondingly.
The electronic control has to be supplied by a separate power supply (24 V DC / 100 mA).

Advantages
 ● High clamping force
 ● Adjustable clamping force
 ● Clamping force monitoring
 ● Can be controlled individually or in common
 ● High operating safety by self-locking spindle drive
 ● Mechanical reclamping by Belleville springs
 ● Swing angle up to 180° available
 ● Overload protection device in the case of collisions with the clamping arm
 ● Electric position monitoring and extensive self-monitoring with diagnostic options
 ● Clamping stroke control possible
 ● Low voltage 24 V
 ● Leakage free
 ● Maintenance free (500,000 cycles).
 ● Code class IP 67

Video
Products (20)
Loading…
body design
parallel drive (20)
position monitoring
with (20)
max. clamping force [kN]
7.9 (20)
metallic wiper
swing angle [°]
swing direction
swing stroke [mm]
3 (20)
total stroke [mm]
26 (20)
clamping arm seat
cone 1:10 (20)
code class
IP 67 (20)
nominal voltage [VDC]
24 (20)
camping force control
with (20)
axial pull force [kN]
3 - 9 (20)
usable clamping stroke [mm]
20 (20)
max. clamping time [s]
3 (20)
IO-Link
Item no. CAD databody designposition monitoringmax. clamping force [kN]metallic wiper
Item no.
CAD data
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
without
Properties
Item no.
CAD data
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
without
Properties
Item no.
CAD data
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
with
Properties
Item no.
CAD data
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
with
Properties
Item no.
CAD data
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
without
Properties
Item no.
CAD data
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
without
Properties
Item no.
CAD data
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
with
Properties
Item no.
CAD data
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
with
Properties
Item no.
CAD data
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
without
Properties
Item no.
CAD data
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
without
Properties
Loading…
Item no.
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
without
swing angle [°]
swing direction
none
swing stroke [mm]
3
total stroke [mm]
26
clamping arm seat
cone 1:10
code class
IP 67
nominal voltage [VDC]
24
camping force control
with
axial pull force [kN]
3 - 9
usable clamping stroke [mm]
20
max. clamping time [s]
3
IO-Link
without
Item no.
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
without
swing angle [°]
swing direction
none
swing stroke [mm]
3
total stroke [mm]
26
clamping arm seat
cone 1:10
code class
IP 67
nominal voltage [VDC]
24
camping force control
with
axial pull force [kN]
3 - 9
usable clamping stroke [mm]
20
max. clamping time [s]
3
IO-Link
with
Item no.
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
with
swing angle [°]
swing direction
none
swing stroke [mm]
3
total stroke [mm]
26
clamping arm seat
cone 1:10
code class
IP 67
nominal voltage [VDC]
24
camping force control
with
axial pull force [kN]
3 - 9
usable clamping stroke [mm]
20
max. clamping time [s]
3
IO-Link
without
Item no.
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
with
swing angle [°]
swing direction
none
swing stroke [mm]
3
total stroke [mm]
26
clamping arm seat
cone 1:10
code class
IP 67
nominal voltage [VDC]
24
camping force control
with
axial pull force [kN]
3 - 9
usable clamping stroke [mm]
20
max. clamping time [s]
3
IO-Link
with
Item no.
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
without
swing angle [°]
90
swing direction
ccw
swing stroke [mm]
3
total stroke [mm]
26
clamping arm seat
cone 1:10
code class
IP 67
nominal voltage [VDC]
24
camping force control
with
axial pull force [kN]
3 - 9
usable clamping stroke [mm]
20
max. clamping time [s]
3
IO-Link
without
Item no.
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
without
swing angle [°]
90
swing direction
ccw
swing stroke [mm]
3
total stroke [mm]
26
clamping arm seat
cone 1:10
code class
IP 67
nominal voltage [VDC]
24
camping force control
with
axial pull force [kN]
3 - 9
usable clamping stroke [mm]
20
max. clamping time [s]
3
IO-Link
with
Item no.
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
with
swing angle [°]
90
swing direction
ccw
swing stroke [mm]
3
total stroke [mm]
26
clamping arm seat
cone 1:10
code class
IP 67
nominal voltage [VDC]
24
camping force control
with
axial pull force [kN]
3 - 9
usable clamping stroke [mm]
20
max. clamping time [s]
3
IO-Link
without
Item no.
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
with
swing angle [°]
90
swing direction
ccw
swing stroke [mm]
3
total stroke [mm]
26
clamping arm seat
cone 1:10
code class
IP 67
nominal voltage [VDC]
24
camping force control
with
axial pull force [kN]
3 - 9
usable clamping stroke [mm]
20
max. clamping time [s]
3
IO-Link
with
Item no.
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
without
swing angle [°]
90
swing direction
cw
swing stroke [mm]
3
total stroke [mm]
26
clamping arm seat
cone 1:10
code class
IP 67
nominal voltage [VDC]
24
camping force control
with
axial pull force [kN]
3 - 9
usable clamping stroke [mm]
20
max. clamping time [s]
3
IO-Link
without
Item no.
body design
parallel drive
position monitoring
with
max. clamping force [kN]
7.9
metallic wiper
without
swing angle [°]
90
swing direction
cw
swing stroke [mm]
3
total stroke [mm]
26
clamping arm seat
cone 1:10
code class
IP 67
nominal voltage [VDC]
24
camping force control
with
axial pull force [kN]
3 - 9
usable clamping stroke [mm]
20
max. clamping time [s]
3
IO-Link
with
Accessories (7)
Item no. CAD data Description
Item no.
CAD data
Description
Metallic wiper for 1835-XXX for piston rod Ø 36 mm as per data sheet B1.8310
Item no.
CAD data
Description
Clamping arm, complete for 18X5-XXX with thread, material: 42CrMo4 max. 200 bar, as per data sheet B1.880
Item no.
CAD data
Description
Cable socket Hirschmann CA3LD as per data sheet B1.8310
Item no.
CAD data
Description
Cable socket Binder 423 12 POL. as per data sheet B1.8310
Item no.
CAD data
Description
Nut M28 x 1.5 mm as per data sheet B1.880
Item no.
CAD data
Description
Clamping arm blank for 18X5-XXX high alloy steel1000....1200 N/mm2 as per data sheet B1.881
Item no.
CAD data
Description
Clamping arm, complete for 18X5-XXX without thread, material: 42CrMo4 max. 200 bar, as per data sheet B1.880
Loading…