Workholding
Contact
Series
D8.756

Intensifier 0.2 – 2.6 l/min

intensification ratio 1.5 to 7.5
max. operating pressure up to 500 bar
double acting
Intensifier 0.2 – 2.6 l/min
Downloads
Catalogue sheet
Operating instructions
Information Series
Description
D 8.756 Hydraulic intensifiers

Description
An oscillating pump piston, that will be automatically reversed in the end positions by a hydraulically-operated valve, is installed in the intensifier. The ratio of the piston areas corresponds to the intensification ratio.
For unhindered flow in the low-pressure range, the pump piston will be bypassed by means of a bypass-line. A pilot-controlled check valve shuts off the high pressure.

Function
The flow rate is supplied without pressure through input IN via the check valves RV1, RV2 and DV to the output H and thereby to the  hydraulic cylinders. With increasing counter pressure the  oscillating pump OP starts working. The flow rate at output H is getting smaller and smaller and is nearly zero when reaching the maximum operating pressure.
The pump holds constant the pressure at H as long as low-pressure is available at IN. Between the ports IN and R there will be leakage of approx. 50 cm3/min, since due to functional reasons the pump elements cannot be sealed without leakage. 
To retract the cylinders, port IN will be depressurised and port R pressurised. At the same time, the check valve DV will be opened and enables free return flow.

Single-acting cylinders
If only single-acting cylinders are connected, a double-acting valve function is required to control the pilot-operated check valves for unclamping (see hydraulic circuit diagram).

Important notes!
The intensifier can produce extremely high hydraulic pressures. The manufacturer of the system must provide effective safety valves for protection against excessive pressures.
The connection of the intensifier must always be double acting. For oil supply, port R must be depressurised. Pump piston and valve slide are fit with minimum clearance. In order to permanently secure the function, it is imperative to install a high-pressure filter at the input IN of the intensifier (see hydraulic circuit diagram). 
As long as pressure is available at IN, the intensifier has an internal leakage between the ports IN and R. If no pressure is available at IN, the pressure can drop in the high-pressure area in case of a leakage.
By the installation of a pilot-controlled check valve at port H a pressure drop is avoided (see hydraulic circuit diagram). This applies in particular to uncoupled systems (clamping pallets).

Video
Functionality
Products (26)
Loading…
type
with continuous flow rate (26)
type
oil - oil (26)
functioning
double acting (26)
hydraulic port
type
high-pressure volume, approx. [cm3]
- (26)
intensification
max. low pressure [bar]
max. high pressure [bar]
max. flow rate low pressure [l/min]
max. flow rate high pressure [l/min]
Item no. CAD datatypetypefunctioninghydraulic port
Item no.
CAD data
type
with continuous flow rate
type
oil - oil
functioning
double acting
hydraulic port
drilled channels
Properties
Item no.
CAD data
type
with continuous flow rate
type
oil - oil
functioning
double acting
hydraulic port
drilled channels
Properties
Item no.
CAD data
type
with continuous flow rate
type
oil - oil
functioning
double acting
hydraulic port
drilled channels
Properties
Item no.
CAD data
type
with continuous flow rate
type
oil - oil
functioning
double acting
hydraulic port
drilled channels
Properties
Item no.
CAD data
type
with continuous flow rate
type
oil - oil
functioning
double acting
hydraulic port
drilled channels
Properties
Item no.
CAD data
type
with continuous flow rate
type
oil - oil
functioning
double acting
hydraulic port
drilled channels
Properties
Loading…
Item no.
type
with continuous flow rate
type
oil - oil
functioning
double acting
hydraulic port
drilled channels
type
manifold-mounting type
high-pressure volume, approx. [cm3]
-
intensification
2
max. low pressure [bar]
207
max. high pressure [bar]
414
max. flow rate low pressure [l/min]
8
max. flow rate high pressure [l/min]
2.4
Item no.
type
with continuous flow rate
type
oil - oil
functioning
double acting
hydraulic port
drilled channels
type
manifold-mounting type
high-pressure volume, approx. [cm3]
-
intensification
2.8
max. low pressure [bar]
178
max. high pressure [bar]
500
max. flow rate low pressure [l/min]
13
max. flow rate high pressure [l/min]
1.4
Item no.
type
with continuous flow rate
type
oil - oil
functioning
double acting
hydraulic port
drilled channels
type
manifold-mounting type
high-pressure volume, approx. [cm3]
-
intensification
3.2
max. low pressure [bar]
155
max. high pressure [bar]
500
max. flow rate low pressure [l/min]
15
max. flow rate high pressure [l/min]
1.6
Item no.
type
with continuous flow rate
type
oil - oil
functioning
double acting
hydraulic port
drilled channels
type
manifold-mounting type
high-pressure volume, approx. [cm3]
-
intensification
4
max. low pressure [bar]
125
max. high pressure [bar]
500
max. flow rate low pressure [l/min]
14
max. flow rate high pressure [l/min]
1.3
Item no.
type
with continuous flow rate
type
oil - oil
functioning
double acting
hydraulic port
drilled channels
type
manifold-mounting type
high-pressure volume, approx. [cm3]
-
intensification
5
max. low pressure [bar]
100
max. high pressure [bar]
500
max. flow rate low pressure [l/min]
14
max. flow rate high pressure [l/min]
1
Item no.
type
with continuous flow rate
type
oil - oil
functioning
double acting
hydraulic port
drilled channels
type
manifold-mounting type
high-pressure volume, approx. [cm3]
-
intensification
6.6
max. low pressure [bar]
75
max. high pressure [bar]
500
max. flow rate low pressure [l/min]
13
max. flow rate high pressure [l/min]
0.4
Accessories (3)
Item no. CAD data Description
Item no.
CAD data
/
Description
Intermediate flange with filter screen as per data sheet D8.756
Item no.
CAD data
Description
Hexagon nut M24 x 1.5 mm - DIN 936 as per data sheet D8.756
Item no.
CAD data
Description
Mounting bracket for intensifier as per data sheet D8.756
Loading…